nginx-1.1.12

[Maxim Dounin]

Hello!

On Tue, Dec 27, 2011 at 11:31:28AM +0200, Boyko Yordanov wrote:

> Hi,
> 
> Not sure which bugfix did this, but nginx 1.1.12 causes redirect 
> loop on one of my vhosts, which is a wordpress blog. Config 
> below. nginx 1.1.11 works fine for this vhost.
> 
>     server {
> 	listen       192.168.2.5:80 default;
> 
>         location / {
> 
>             location ~ /\.ht {
>                 deny  all;
>             }
> 
>             proxy_redirect off;
>             proxy_set_header   Host             $host;
>             proxy_set_header   X-Real-IP        $remote_addr;
>             proxy_set_header   X-Forwarded-For  $proxy_add_x_forwarded_for;
> 
>             client_max_body_size       25m;
>             client_body_buffer_size    128k;
> 
>             proxy_connect_timeout      300;
>             proxy_send_timeout         300;
>             proxy_read_timeout         300;
> 
>             proxy_buffering on;
>             proxy_buffer_size          32k;
>             proxy_buffers              32 4k;
>             proxy_busy_buffers_size    64k;
>             proxy_max_temp_file_size 0;
> 
>             access_log off;
>             proxy_pass   http://192.168.2.5:8080;
> 
>         }

Could you please show debug log?  See 
http://wiki.nginx.org/Debugging for details.

Maxim Dounin

> 
> 
> On Dec 26, 2011, at 5:48 PM, Maxim Dounin wrote:
> 
> > Changes with nginx 1.1.12                                        26 Dec 2011
> > 
> >    *) Change: a "proxy_pass" directive without URI part now uses changed
> >       URI after redirection with the "error_page" directive.
> >       Thanks to Lanshun Zhou.
> > 
> >    *) Feature: the "proxy/fastcgi/scgi/uwsgi_cache_lock",
> >       "proxy/fastcgi/scgi/uwsgi_cache_lock_timeout" directives.
> > 
> >    *) Feature: the "pcre_jit" directive.
> > 
> >    *) Feature: the "if" SSI command supports captures in regular
> >       expressions.
> > 
> >    *) Bugfix: the "if" SSI command did not work inside the "block" command.
> > 
> >    *) Bugfix: the "limit_conn_log_level" and "limit_req_log_level"
> >       directives might not work.
> > 
> >    *) Bugfix: the "limit_rate" directive did not allow to use full
> >       throughput, even if limit value was very high.
> > 
> >    *) Bugfix: the "sendfile_max_chunk" directive did not work, if the
> >       "limit_rate" directive was used.
> > 
> >    *) Bugfix: a "proxy_pass" directive without URI part always used
> >       original request URI if variables were used.
> > 
> >    *) Bugfix: a "proxy_pass" directive without URI part might use original
> >       request after redirection with the "try_files" directive.
> >       Thanks to Lanshun Zhou.
> > 
> >    *) Bugfix: in the ngx_http_scgi_module.
> > 
> >    *) Bugfix: in the ngx_http_mp4_module.
> > 
> >    *) Bugfix: nginx could not be built on Solaris; the bug had appeared in
> >       1.1.9.
> > 
> 
> _______________________________________________
> nginx mailing list
> nginx at nginx.org
> http://mailman.nginx.org/mailman/listinfo/nginx